16/32bit ARM 9 Core

    16/32bit ARM 7 Core

    8bit 80C51 Core

   
HOME > NXP Device >ARM7 >LPC2109/19/29 


LPC2109/2119/2129

Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN


INTRODUCTION | SPECIFICATION | PACKAGE | SUPPORT

LPC2109/2119/2129

16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 64/128/256 kB of embedded high-speed flash memory.

LPC2109
Microcontroller with 64KB ISP/IAP flash, 10-bit ADC, 1 CAN channel
LPC2119
Microcontroller with 128KB ISP/IAP flash, 10-bit ADC, 2 CAN channels
LPC2129
Microcontroller with 256KB ISP/IAP flash, 10-bit ADC, 2 CAN channels

< Key features brought by LPC2109/2119/2129/01 devices >

  • Fast GPIO ports enable port pin toggling up to 3.5 times faster than the original device. They also allow for a port pin to be read at any time regardless of its function.
  • Dedicated result registers for ADC(s) reduce interrupt overhead. The ADC pads are 5 V tolerant when configured for digital I/O function(s).
  • UART0/1 include fractional baud rate generator, auto-bauding capabilities and handshake flow-control fully implemented in hardware.
  • Buffered SSP serial controller supporting SPI, 4-wire SSI, and Microwire formats.
  • SPI programmable data length and master mode enhancement.
  • Diversified Code Read Protection (CRP) enables different security levels to be implemented. This feature is available in LPC2109/2119/2129/00 devices as well.
  • General purpose timers can operate as external event counters.

< Key features common for all devices>

  • 16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.
  • 8/16 kB on-chip static RAM.
  • 64/128/256 kB on-chip flash program memory. 128-bit wide interface/accelerator enables high speed 60 MHz operation.
  • In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or full chip erase takes 400 ms.
  • EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service routines can continue to execute while the foreground task is debugged with the on-chip RealMonitor software.
  • Embedded Trace Macrocell (ETM) enables non-intrusive high speed real-time tracing of instruction execution.
  • Two interconnected CAN interfaces (one for LPC2109) with advanced acceptance filters.
  • Four-channel 10-bit A/D converter with conversion time as low as 2.44 us.
  • Multiple serial interfaces including two UARTs (16C550), Fast I 2 C-bus (400 kbit/s) and two SPIs.
  • 60 MHz maximum CPU clock available from programmable on-chip Phase-Locked Loop with settling time of 100 us.
  • Vectored Interrupt Controller with configurable priorities and vector addresses.
  • Two 32-bit timers (with four capture and four compare channels), PWM unit (six outputs), Real-Time Clock (RTC) and watchdog.
  • Up to forty-six 5 V tolerant general purpose I/O pins. Up to nine edge or level sensitive external interrupt pins available.
  • On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.
  • Two low power modes, Idle and Power-down.
  • Processor wake-up from Power-down mode via external interrupt.
  • Individual enable/disable of peripheral functions for power optimization.
  • Dual power supply:
    • CPU operating voltage range of 1.65 V to 1.95 V (1.8 V +- 0.15 V).
    • I/O power supply range of 3.0 V to 3.6 V (3.3 V +- 10 pct) with 5 V tolerant I/O pads.

<Block Diagram >

< Pinning >

 

Product
Ordering Code
LPC2109FBD64/00 9352 843 08151
LPC2109FBD64/01 9352 848 91151
LPC2119FBD64 9352 747 36151
LPC2119FBD64/00 9352 823 52151
LPC2119FBD64/01 9352 848 86151
LPC2129FBD64 9352 747 37151
LPC2129FBD64/00 9352 823 54151
LPC2129FBD64/01 9352 848 89151
- Applica Notes -  
- AN10254_2; NXP ARM LPC microcontroller family
- AN10255_2; Philips LPC210x microcontroller family
- AN10256-2 Using IAP for LPC2000 ARM devices
- AN10302_4; Using the Philips LPC2000 Flash utility with the Keil MCB2100 and IAR LPC210x Kickstart evaluation boards
- AN10331_1; Philips LPC2xxx family phase lock loop
- AN10369_1; UART/SPI/I2C code examples
- AN10381_1; Nesting of interrupts in the LPC2000
- AN10403_1; Connecting ethernet interface with LPC2000
- AN10404_1; Initialization code/hints for the LPC2000 family
- AN10413_2; uC/OS-II Time Management in LPC2000
- AN10513_1; Brushed DC motor control using the LPC2101
- AN10576_1; Migrating to the LPC2300/2400 family
   
- Support Documents-  
- NXP_flash_utility : ARM flash utility
-75015814; 70-MHz, 32-bit microcontroller with ARM7 core LPC210x
- 75016051: The choice for embedded Technologies
- ES_LPC2109_1; Errata sheet LPC2109
- ES_LPC2119_1; Errata sheet LPC2119
- ES_LPC2129_1; Errata sheet LPC2129
- LPC2109_19_29 User Manual
   
- Technical Notes -  
- TN06004_LPC2000 ADC Code Example
- TN06005_LPC2000_I2C; LPC2000 I2C slave code example
- LPC2000 USB Design Guide Line
- UUencode


본사. 121-703 서울시 마포구 마포대로4다길 18 (마포동) 1302호 | Tel. 02-704-7111 | Fax. 02-704-7211
매장. 152-721 서울시 구로구 경인로53길 15 (구로동) 가동 2315호 | Tel. 02-6679-1400 | Mob. 010-5703-7111
Copyright ⓒ 1996 - 2014 VAS Corporation, All Rights Reserved.