16/32bit ARM 9 Core

    16/32bit ARM 7 Core

    8bit 80C51 Core

   
HOME > NXP Device >ARM7 >LPC2210/2220  


LPC2210/2220

16/32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface



LPC2210/2220

LPC2210/2220 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support.

 

LPC2210
Microcontroller with 10-bit ADC, external memory interface
LPC2220
Microcontroller with 10-bit ADC, external memory interface

< Key Features >

  • 16/64 kB on-chip static RAM (LPC2210/2220).
  • Serial bootloader using UART0 provides in-system download and programming capabilities.
  • EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the on-chip RealMonitor software as well as high-speed real-time tracing of instruction execution.
  • Eight channel 10-bit ADC with conversion time as low as 2.44 us.
    • LPC2210/01 and LPC2220 only: Dedicated result registers for ADC(s) reduce interrupt overhead. The ADC pads are 5 V tolerant when configured for digital I/O function(s).
  • Two 32-bit timers (LPC2220 and LPC2210/01 also external event counters) with four capture and four compare channels, PWM unit (six outputs), Real-Time Clock (RTC), and watchdog.
  • Multiple serial interfaces including two UARTs (16C550), Fast I 2 C-bus (400 kbit/s) and two SPIs.
    • LPC2210/01 and LPC2220 only: A Synchronous Serial Port (SSP) with data buffers and variable length transfers can be selected to replace one SPI.
    • LPC2210/01 and LPC2220 only: UART0/1 include fractional baud rate generator, auto-bauding capabilities, and handshake flow-control fully implemented in hardware.
  • Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses.
  • Configurable external memory interface with up to four banks, each up to 16 MB and 8/16/32-bit data width.
  • Up to 76 general purpose pins (5 V tolerant) capable. Up to nine edge/level sensitive external interrupt pins available.
    • LPC2210/01 and LPC2220 only: Fast GPIO ports enable port pin toggling up to 3.5 times faster than the original device. They also allow for a port pin to be read at any time regardless of its function.
  • 60 MHz (LPC2210) and 75 MHz (LPC2210/01 and LPC2220) maximum CPU clock available from programmable on-chip Phase-Locked Loop (PLL) with settling time of 100 us.
  • On-chip integrated oscillator operates with external crystal in range of 1 MHz to 30 MHz and with external oscillator up to 50 MHz.
  • Power saving modes include Idle and Power-down.
  • Processor wake-up from Power-down mode via external interrupt.
  • Individual enable/disable of peripheral functions for power optimization.
  • Dual power supply:
    • CPU operating voltage range of 1.65 V to 1.95 V (1.8 V +- 0.15 V).
    • I/O power supply range of 3.0 V to 3.6 V (3.3 V +- 10 pct) with 5 V tolerant I/O pads. 16/32-bit ARM7TDMI-S processor

<Block Diagram >

< Pinning >


Product
Ordering Code
LPC2210FBD144 9352 756 83551
LPC2210FBD144/01 9352 820 78551
LPC2220FBD144 9352 788 29551
LPC2220FET144/G 9352 812 16551
- Application Notes -  
- AN10254_2; Philips ARM LPC microcontroller family
- AN10256-2 Using IAP for LPC2000 ARM devices
- AN10302_4; Using the Philips LPC2000 Flash utility with the Keil MCB2100 and IAR LPC210x Kickstart evaluation boards
- AN10331_1; Philips LPC2xxx family phase lock loop
- AN10381_1; Nesting of interrupts in the LPC2000
- AN10389_1; Getting started uClinux with LPC22x
- AN10403_1; Connecting ethernet interface with LPC2000
- AN10413_2; uC/OS-II Time Management in LPC2000
- AN10414_1; Handling of spurious interrupts in the LPC2000
- AN10600_1; Connecting NXP ARM-based microcontroller LPC2200 to small page NAND flash
   
- Support Documents-  
- 75012679: LPC2210 Big Performance Low Power Leaflet
- 75013969: LPC221x Family
- 75015812; 72MHz, 32-bit microcontroller with ARM7 LPC23xx
- 75016051: The choice for embedded Technologies
- Errata Sheet (LPC2210)
- Errata Sheet (LPC2220)
- LPC2210/2220 User Manual
   
- Technical Notes -  
- TN05007 LPC2xxx UART Transmitter Code Example
- TN06001 LPC2xxx SPI Master Code Example
- TN06002 LPC2000 EINT Code Example
- TN06004 LPC2000 ADC Code Example
- LPC2000 I2C Slave Code Example
- LPC2000 USB Design Guide Line
- UBOOT

본사. 121-703 서울시 마포구 마포대로4다길 18 (마포동) 1302호 | Tel. 02-704-7111 | Fax. 02-704-7211
매장. 152-721 서울시 구로구 경인로53길 15 (구로동) 가동 2315호 | Tel. 02-6679-1400 | Mob. 010-5703-7111
Copyright ⓒ 1996 - 2014 VAS Corporation, All Rights Reserved.